Screws
Lag Screws (Lag Bolts) Manufacturer, Wholesaler, Supplier & Exporter
Lag Screws (Lag Bolts) manufacturer, wholesaler, supplier and exporter from India. Global Fasteners Exports is a trading and export company: our lag screws (lag bolts) are made to DIN 571, ASME B18.2.1 standards by partner factories and supplied to importers, distributors and OEMs in 222+ countries from 5,000 pcs, or a half or full container, at competitive prices below the average wholesale price.
Lag screws are heavy hex-head wood screws made to pull timber members together where a through-bolt cannot reach the back of the joint. Our partner factories make them to DIN 571 and ASME B18.2.1 in carbon steel, hot-dip galvanized and stainless steel, and we ship them in full or part container loads to timber-frame builders, utility contractors and hardware wholesalers.
A lag screw does the job of a bolt where only one face of the joint is reachable. The thread bites into the timber, and the hex head lets an installer apply real torque with a socket, which a screwdriver-driven wood screw cannot match. That is why lag screws appear in decks, timber frames and pole-line hardware rather than in furniture.
Two things decide whether a lag screw performs: the pilot hole and the embedment. The unthreaded shank should pass through the first member without gripping, and the threaded part must enter the second member deeply enough, commonly several times the screw diameter, to carry the design load. A screw that is too short fails by pulling out, however strong its steel.
For export orders, the finish matters as much as the dimensions. Buyers in humid or coastal markets usually ask for hot-dip galvanized or stainless screws, and buyers in cold-climate timber construction often specify zinc plating with a washer under the head. We confirm standard, diameter, length and finish before production.

Minimum order and container quantity
Minimum order
5,000 pcs
or half / full container, as per your requirement
Half container (20ft)
125,000-225,000 pcs
Full container (20ft)
250,000-450,000 pcs
A standard 20ft container (~20 tons) holds approximately 250,000-450,000 pieces of lag screws in common sizes (M8-M10). Exact quantity depends on length and diameter and is confirmed at quote time.
The minimum order is 5,000 pcs, so you don't need a full container to order: half-container and smaller LCL orders are available as well. Hurain Engitech & Trade — the group Global Fasteners Exports operates under — regularly ships smaller, partial-container (LCL) orders of just a few pallets or boxes for buyers who don't yet need FCL volume, consolidated with other cargo to keep freight cost reasonable.
Lag Screws (Lag Bolts): photos by size and detail



Specifications
Standards
DIN 571 (hexagon head wood screws), ASME B18.2.1 (square and hex lag screws), and BIS equivalents on request.
Size range
M6 to M20 in metric (6 to 20 mm); 1/4" to 1" in imperial; lengths from 30 mm to 400 mm.
Thread
Coarse wood-screw thread over part of the length, with a gimlet or cone point to start in a pilot hole.
Finish
Plain, zinc plated, hot-dip galvanized for treated or outdoor timber, and stainless steel A2 / A4.
Applications
Timber framing
Joining beams, posts and ledgers where a nut cannot be fitted on the far side.
Decks and pergolas
Fixing ledger boards and heavy rails to house frames and posts.
Utility and fencing work
Brackets and cross-arms fixed to wooden poles and heavy fence posts.
Machinery on timber
Mounting equipment bases and rails onto wooden skids and floors.
Materials Available
Steel
Corrosion-resistant
Coatings
Every batch can be released against DIN 571 or ASME B18.2.1, including head and thread dimensions, coating thickness and a torque or bend check on a sample, with mill test certificates and dimensional inspection reports supplied on request.
How We Supply & Export This Product
- 1
Order & spec confirmation
Confirm the standard, size, material, finish and quantity of the lag screws (lag bolts), and any drawing or sample, before production begins.
- 2
Manufacturing at partner factories
The head is cold-forged, the thread is rolled to the lag-screw profile and the point is formed, then the screws are coated; head height and thread form are checked in process.
- 3
Quality inspection
Batch sampling for head dimensions, thread profile, length, coating thickness and a bend test, before packing.
- 4
Export packing & documentation
Corrosion-protected cartons and pallets of lag screws (lag bolts), container loading, and full export documents (invoice, packing list, certificate of origin, MTC).
Export Track Record
Shipped as full container loads (FCL) and LCL pallets of lag screws (lag bolts) to distributors, OEM buyers and project contractors across multiple continents.
Real-World Use Cases
Deck ledger boards
Fixing the deck ledger to the house rim joist, with washers under the heads to spread the load.
Heavy timber connections
Joining large posts and beams in timber-frame and pergola structures.
Pole-line brackets
Attaching steel brackets and cross-arms to treated wooden poles.
Machine bases on timber
Anchoring equipment frames to wooden skids, sleepers and floors.
Common Mistakes Buyers Make
Driving without a pilot hole
The timber splits or the screw shears, especially in hardwood or near an edge.
Using impact drivers at full speed
The hex head or the thread is stripped before the screw is seated; drive with a wrench or a controlled socket.
Choosing plain steel for treated timber
Copper-based preservatives corrode plain and thin zinc finishes within a few seasons.
Too little thread in the second member
A short embedment makes the joint fail by pull-out even if the steel is strong enough.
Glossary of Terms
- Pilot hole
- A pre-drilled hole, smaller than the screw, that guides the screw and prevents the timber splitting.
- Shank
- The unthreaded part under the head of a partly threaded screw.
- Embedment
- The length of thread that is inside the second timber member.
- Coach screw
- The British name for a lag screw.
- DIN 571
- The German standard for hexagon head wood screws, the metric equivalent of the American lag screw.
Quality Inspection We Perform
Dimensional inspection
Thread gauge, length, diameter, and head/drive geometry checked against the specified standard.
Material verification
Grade and material composition confirmed against the order specification, with mill test certificates on request.
Mechanical testing
Tensile strength, hardness, and proof-load testing on sample batches, particularly for structural and high-tensile grades.
Finish & coating check
Plating thickness, galvanizing coverage, or passivation quality inspected before packing.
HS Code & Customs Classification
Most fasteners fall under HS Chapter 73 (articles of iron or steel) or Chapter 74/76 for brass and aluminum items — the exact 8-10 digit subheading depends on the specific product and material. We include the HS code on the commercial invoice; confirm the applicable import duty with your customs broker, since rates vary by country and trade agreement.
Packaging & Export Labeling
Export packing is chosen to survive ocean freight and container loading without corrosion or damage: corrosion-protected paper or oil coating where needed, then cartons, drums, or bulk bags, palletized or crated for the container. We can match specific labeling, barcoding, or carton-marking requirements for OEM and repeat buyers.
Countries We Export Lag Screws (Lag Bolts) To
All countries and cities for Lag Screws (Lag Bolts) →Frequently Asked Questions
Related Products
Competitive export pricing
The best price on lag screws (lag bolts) for buyers worldwide
Global Fasteners Exports provides competitive export prices for worldwide customers, below the average wholesale price, because we buy in volume directly from our partner factories. With 16+ years of experience, we are honored to export to 222+ countries and to cooperate with 10,000+ customers around the world. Are you looking for lag screws (lag bolts) for your brand or wholesale business worldwide? Global Fasteners Exports is your best choice. Lag screws are heavy, so buying a full range of lengths in one container lowers the freight per piece, and length, thread, coating and head type can be customized. Minimum order 5,000 pieces, or a half container or a full container as per your requirement. Customized available.
Reviewed by Khalil Syed, Founder, Hurain Engitech & Trade · Last updated
Factory-direct
Priced below the average wholesale rate
16+
Years of experience
222+
Countries we export to
10,000+
Customers worldwide
5,000 pcs
Minimum order, or half / full container
About us
Trusted Lag Screws (Lag Bolts) manufacturer, supplier and exporter from India
Global Fasteners Exports is a trading and export company that supplies lag screws (lag bolts) from India, with quality checks, export packing and complete shipping documents.
Our lag screws (lag bolts) are manufactured to your grade, size and packing by our partner factories, and we sell and ship them to importers, distributors, OEMs and project buyers. Buying through us means one supplier for lag screws (lag bolts) and for the other screws you need, one inspection and one set of export documents.
16+
Years of experience
40+
Our team
10,000+
Happy customers
41
Fastener product lines
222
Countries we supply
FCL · LCL
Container export, door-to-port
Our vision in India
Our vision is to make sourcing lag screws (lag bolts) simple and dependable for every buyer in India and abroad: clear specifications, honest information about who makes the product, and a supplier that answers questions before and after the order.
Our mission in India
Our mission is to supply lag screws (lag bolts) at competitive prices, below the average wholesale price, through our partner factories and bulk buying, with transparent quotations, inspection before dispatch and reliable delivery from India. Send your specification and quantity to get a price you can compare.
Ready to order Lag Screws (Lag Bolts)?
Send your quantities, grade, standard, and destination port for a quote.

