Screws
Decking Screws Manufacturer, Wholesaler, Supplier & Exporter
Decking Screws manufacturer, wholesaler, supplier and exporter from India. Global Fasteners Exports is a trading and export company: our decking screws are made to ASTM B117, ISO 9227 standards by partner factories and supplied to importers, distributors and OEMs in 222+ countries from 10,000 pcs, or a half or full container, at competitive prices below the average wholesale price.
Decking screws are made to fix deck boards to joists without splitting them and without rusting for years outdoors. They have a self-countersinking head, a star (Torx) drive and a thread that pulls the board down. Our partner factories make them in coated carbon steel and in A2 and A4 stainless steel for timber and composite decking, and we export them in cartons and pallets.
A decking screw has to do three things that a general wood screw does not: sink its own head, avoid splitting the end of a board, and survive outdoors for the life of the deck. The self-countersinking head cuts its own seat, the nibs under the head widen the hole in the board, and the coating resists the chemicals in treated timber.
The coating is where decking screws differ most. Thin zinc is not enough for modern treated timber, so ceramic and polymer coatings are used, and stainless steel for coastal or hardwood decks. Buyers should ask for salt-spray hours, not just the word 'coated'.
Packing and quantity matter in this line. Decking screws are bought by contractors in boxes of a few hundred and by wholesalers in cartons of thousands, and each market has its own preferred size, so we pack to the buyer's box and carton specification.

Minimum order and container quantity
Minimum order
10,000 pcs
or half / full container, as per your requirement
Half container (20ft)
1-2 million pcs
Full container (20ft)
2-4 million pcs
A standard 20ft container (~20 tons) typically holds 2,000,000-4,000,000 pieces of decking screws in common sizes (4.2 mm x 50 mm to 5.0 mm x 60 mm). Exact quantity depends on length and diameter and is confirmed at quote time.
The minimum order is 10,000 pcs, so you don't need a full container to order: half-container and smaller LCL orders are available as well. Hurain Engitech & Trade — the group Global Fasteners Exports operates under — regularly ships smaller, partial-container (LCL) orders of just a few pallets or boxes for buyers who don't yet need FCL volume, consolidated with other cargo to keep freight cost reasonable.
Decking Screws: photos by size and detail



Specifications
Standards
No single ISO standard: specified by diameter, length, head, drive and coating, with salt-spray hours per ASTM B117 or ISO 9227.
Size range
4.0 mm to 5.5 mm diameter by 40 mm to 100 mm (#8 and #10); lengths about 2.5 times the board thickness.
Head and drive
Self-countersinking or trumpet head with Torx T20 or T25; some with a reduced shank near the head to limit splitting.
Finish
Ceramic or polymer coated carbon steel for treated timber, A2 (304) and A4 (316) stainless for coastal sites and hardwoods.
Applications
Timber decks
Fixing softwood and hardwood boards to joists in gardens, patios and boardwalks.
Composite decking
Fixing wood-plastic boards with a reduced-head screw that limits mushrooming.
Pergolas and fencing
Fixing slats, rails and cladding in outdoor timber structures.
Boardwalks and marinas
Stainless screws in wet and coastal conditions.
Materials Available
Coated steel
Stainless
Head options
Every batch can be released against the buyer's drawing and specification, including head, drive, torque-to-failure and salt-spray hours on the coating, with mill test certificates and dimensional inspection reports supplied on request.
How We Supply & Export This Product
- 1
Order & spec confirmation
Confirm the standard, size, material, finish and quantity of the decking screws, and any drawing or sample, before production begins.
- 2
Manufacturing at partner factories
Wire is cold-headed, the Torx recess is formed, the thread is rolled with a nibbed or cutting point, then the screws are hardened and coated; recess and thread are checked in process.
- 3
Quality inspection
Batch sampling for torsional strength, drive fit, thread, length, coating thickness and a salt-spray test, before packing.
- 4
Export packing & documentation
Corrosion-protected cartons and pallets of decking screws, container loading, and full export documents (invoice, packing list, certificate of origin, MTC).
Export Track Record
Shipped as full container loads (FCL) and LCL pallets of decking screws to distributors, OEM buyers and project contractors across multiple continents.
Real-World Use Cases
Softwood deck boards
Coated screws at board ends and across joists, with pre-drilling near the ends.
Hardwood decking
Stainless steel screws with a hardened tip, usually with a pilot hole.
Composite boards
Reduced-head screws that avoid mushrooming the board around the screw.
Marine boardwalks
A4 stainless screws in constantly wet and salty conditions.
Common Mistakes Buyers Make
Using zinc-plated screws in treated timber
The screws corrode and the boards loosen within a few years.
Fixing too close to the board end
The board splits; pre-drill or use screws with a split-limiting tip near the ends.
Over-driving the head
The head sinks too far, tears the surface and holds less; set the clutch on the driver.
Mixing stainless screws with plain steel fixings
Different metals in wet conditions can cause staining and galvanic corrosion at the contact points.
Glossary of Terms
- Self-countersinking head
- A head with ribs or a cutter underneath that forms its own seat in the board.
- Torx (star) drive
- A six-point star recess that resists cam-out at high torque.
- Salt spray
- A standard corrosion test (ISO 9227 / ASTM B117) that reports hours before red rust appears.
- Reduced shank
- A thinner section under the head that cuts down the force on the board and the risk of splitting.
- ACQ timber
- Pressure-treated timber with copper-based preservative, which corrodes plain steel.
Quality Inspection We Perform
Dimensional inspection
Thread gauge, length, diameter, and head/drive geometry checked against the specified standard.
Material verification
Grade and material composition confirmed against the order specification, with mill test certificates on request.
Mechanical testing
Tensile strength, hardness, and proof-load testing on sample batches, particularly for structural and high-tensile grades.
Finish & coating check
Plating thickness, galvanizing coverage, or passivation quality inspected before packing.
HS Code & Customs Classification
Most fasteners fall under HS Chapter 73 (articles of iron or steel) or Chapter 74/76 for brass and aluminum items — the exact 8-10 digit subheading depends on the specific product and material. We include the HS code on the commercial invoice; confirm the applicable import duty with your customs broker, since rates vary by country and trade agreement.
Packaging & Export Labeling
Export packing is chosen to survive ocean freight and container loading without corrosion or damage: corrosion-protected paper or oil coating where needed, then cartons, drums, or bulk bags, palletized or crated for the container. We can match specific labeling, barcoding, or carton-marking requirements for OEM and repeat buyers.
Countries We Export Decking Screws To
All countries and cities for Decking Screws →Frequently Asked Questions
Related Products
Competitive export pricing
The best price on decking screws for buyers worldwide
Global Fasteners Exports provides competitive export prices for worldwide customers, below the average wholesale price, because we buy in volume directly from our partner factories. With 16+ years of experience, we are honored to export to 222+ countries and to cooperate with 10,000+ customers around the world. Are you looking for decking screws for your brand or wholesale business worldwide? Global Fasteners Exports is your best choice. Decking screws are packed in the millions, so a container mix of sizes keeps the unit price low, and head, drive, length, coating and box size can be customized. Minimum order 10,000 pieces, or a half container or a full container as per your requirement. Customized available.
Reviewed by Khalil Syed, Founder, Hurain Engitech & Trade · Last updated
Factory-direct
Priced below the average wholesale rate
16+
Years of experience
222+
Countries we export to
10,000+
Customers worldwide
10,000 pcs
Minimum order, or half / full container
About us
Trusted Decking Screws manufacturer, supplier and exporter from India
Global Fasteners Exports is a trading and export company that supplies decking screws from India, with quality checks, export packing and complete shipping documents.
Our decking screws are manufactured to your grade, size and packing by our partner factories, and we sell and ship them to importers, distributors, OEMs and project buyers. Buying through us means one supplier for decking screws and for the other screws you need, one inspection and one set of export documents.
16+
Years of experience
40+
Our team
10,000+
Happy customers
41
Fastener product lines
222
Countries we supply
FCL · LCL
Container export, door-to-port
Our vision in India
Our vision is to make sourcing decking screws simple and dependable for every buyer in India and abroad: clear specifications, honest information about who makes the product, and a supplier that answers questions before and after the order.
Our mission in India
Our mission is to supply decking screws at competitive prices, below the average wholesale price, through our partner factories and bulk buying, with transparent quotations, inspection before dispatch and reliable delivery from India. Send your specification and quantity to get a price you can compare.
Ready to order Decking Screws?
Send your quantities, grade, standard, and destination port for a quote.

