Anchors
Concrete Screws Manufacturer, Wholesaler, Supplier & Exporter
Concrete Screws manufacturer, wholesaler, supplier and exporter from India. Global Fasteners Exports is a trading and export company: our concrete screws are made to DIN, ISO and ASTM standards by partner factories and supplied to importers, distributors and OEMs in 222+ countries from 10,000 pcs, or a half or full container, at competitive prices below the average wholesale price.
A concrete screw cuts its own thread into a pre-drilled hole in concrete, brick or block, so it needs no expansion sleeve or chemical. It can be removed and reused, and it is quick to install. Our partner factories make concrete screws in hardened carbon steel with corrosion-resistant coatings and in stainless steel, in hex, countersunk and pan-head forms.
A concrete screw is a hard screw that is cut into the base material itself. The thread is hardened so that it can cut a mating thread in concrete as it is driven, which gives a mechanical key, without expansion forces on the hole edge. This makes it a good choice near edges and in thin sections.
The weak point is the installation. The drill-hole diameter, the depth and the cleanliness of the hole control how the screw performs, and the manufacturer's tables are written for those exact conditions. A hole that is too large, or filled with dust, can halve the holding, so installers must follow the instruction.
For loads that matter, such as overhead services or racking, the buyer should ask for the approval and the load data for the exact screw and the base material. We supply concrete screws with their specification sheet and test certificates and help the buyer match the product to the use.

Minimum order and container quantity
Minimum order
10,000 pcs
or half / full container, as per your requirement
Half container (20ft)
400,000-800,000 pcs
Full container (20ft)
800,000-1.6 million pcs
A standard 20ft container (~20 tons) holds approximately 800,000-1,600,000 pieces of concrete screws in common sizes (6 mm-7.5 mm). Exact quantity depends on diameter and length and is confirmed at quote time.
The minimum order is 10,000 pcs, so you don't need a full container to order: half-container and smaller LCL orders are available as well. Hurain Engitech & Trade — the group Global Fasteners Exports operates under — regularly ships smaller, partial-container (LCL) orders of just a few pallets or boxes for buyers who don't yet need FCL volume, consolidated with other cargo to keep freight cost reasonable.
Concrete Screws: photos by size and detail



Specifications
Standards
European technical assessment practice (EAD 332347-00-0601 for concrete screws) and buyer's specification; load tables from the manufacturer.
Size range
6 mm, 7.5 mm, 10 mm, 12 mm and 14 mm diameters by 40 mm to 250 mm.
Head types
Hex head with washer, countersunk with Torx, pan head, and internal-thread versions.
Finish
Blue or silver zinc, zinc-nickel, long-life corrosion coating, and stainless steel A4 / 410.
Applications
Frames and window fixings
Fixing door and window frames and battens to masonry.
Electrical and mechanical services
Cable trays, brackets and ducts fixed to concrete.
Racking and shelving
Light and medium loads in warehouses.
Cladding sub-frames
Fixing rails and brackets to a concrete wall.
Materials Available
Hardened steel
Corrosion-resistant
Heads
Every batch can be released against the buyer's specification and manufacturer's load tables, including hardness, thread, drill-hole size and a torque and pull-out test on a sample, with mill test certificates and dimensional inspection reports supplied on request.
How We Supply & Export This Product
- 1
Order & spec confirmation
Confirm the standard, size, material, finish and quantity of the concrete screws, and any drawing or sample, before production begins.
- 2
Manufacturing at partner factories
The steel is cold-headed, a hardened cutting thread is rolled, and the screws are heat treated and coated; the thread profile and hardness are checked in process.
- 3
Quality inspection
Batch sampling for hardness, thread profile, head, coating and a torque-to-failure test, before packing.
- 4
Export packing & documentation
Corrosion-protected cartons and pallets of concrete screws, container loading, and full export documents (invoice, packing list, certificate of origin, MTC).
Export Track Record
Shipped as full container loads (FCL) and LCL pallets of concrete screws to distributors, OEM buyers and project contractors across multiple continents.
Real-World Use Cases
Door and window frames
Countersunk screws through the frame into the masonry.
Cable tray brackets
Hex screws fixing brackets to a concrete ceiling.
Warehouse racking
Fixing base plates to a concrete slab.
Façade rails
Screws holding sub-frames to a wall.
Common Mistakes Buyers Make
Wrong drill diameter
A hole too wide gives a loose fit, and too small snaps the screw; follow the instruction.
Not clearing the dust
Dust in the hole prevents the thread from cutting and lowers the load.
Over-torquing with an impact driver
The screw shears or strips the thread; use a controlled driver.
Using them in the wrong base material
Aerated concrete and hollow block need an approved product.
Glossary of Terms
- Self-cutting thread
- A hardened thread that forms its own mating thread in the base material.
- Hammer drill
- A drill with a hammering action used to make holes in concrete and masonry.
- Base material
- The concrete, brick or block that the screw is fixed into.
- Embedment depth
- The length of the screw that is inside the base material.
- EAD
- A European Assessment Document that sets the tests for an anchor product.
Quality Inspection We Perform
Dimensional inspection
Thread gauge, length, diameter, and head/drive geometry checked against the specified standard.
Material verification
Grade and material composition confirmed against the order specification, with mill test certificates on request.
Mechanical testing
Tensile strength, hardness, and proof-load testing on sample batches, particularly for structural and high-tensile grades.
Finish & coating check
Plating thickness, galvanizing coverage, or passivation quality inspected before packing.
HS Code & Customs Classification
Most fasteners fall under HS Chapter 73 (articles of iron or steel) or Chapter 74/76 for brass and aluminum items — the exact 8-10 digit subheading depends on the specific product and material. We include the HS code on the commercial invoice; confirm the applicable import duty with your customs broker, since rates vary by country and trade agreement.
Packaging & Export Labeling
Export packing is chosen to survive ocean freight and container loading without corrosion or damage: corrosion-protected paper or oil coating where needed, then cartons, drums, or bulk bags, palletized or crated for the container. We can match specific labeling, barcoding, or carton-marking requirements for OEM and repeat buyers.
Countries We Export Concrete Screws To
All countries and cities for Concrete Screws →Frequently Asked Questions
Related Products
Competitive export pricing
The best price on concrete screws for buyers worldwide
Global Fasteners Exports provides competitive export prices for worldwide customers, below the average wholesale price, because we buy in volume directly from our partner factories. With 16+ years of experience, we are honored to export to 222+ countries and to cooperate with 10,000+ customers around the world. Are you looking for concrete screws for your brand or wholesale business worldwide? Global Fasteners Exports is your best choice. Concrete screws are produced in large volume, so wholesale pricing applies from the first order, and diameter, length, head, coating and stainless grade can be customized. Minimum order 10,000 pieces, or a half container or a full container as per your requirement. Customized available.
Reviewed by Khalil Syed, Founder, Hurain Engitech & Trade · Last updated
Factory-direct
Priced below the average wholesale rate
16+
Years of experience
222+
Countries we export to
10,000+
Customers worldwide
10,000 pcs
Minimum order, or half / full container
About us
Trusted Concrete Screws manufacturer, supplier and exporter from India
Global Fasteners Exports is a trading and export company that supplies concrete screws from India, with quality checks, export packing and complete shipping documents.
Our concrete screws are manufactured to your grade, size and packing by our partner factories, and we sell and ship them to importers, distributors, OEMs and project buyers. Buying through us means one supplier for concrete screws and for the other anchors you need, one inspection and one set of export documents.
16+
Years of experience
40+
Our team
10,000+
Happy customers
41
Fastener product lines
222
Countries we supply
FCL · LCL
Container export, door-to-port
Our vision in India
Our vision is to make sourcing concrete screws simple and dependable for every buyer in India and abroad: clear specifications, honest information about who makes the product, and a supplier that answers questions before and after the order.
Our mission in India
Our mission is to supply concrete screws at competitive prices, below the average wholesale price, through our partner factories and bulk buying, with transparent quotations, inspection before dispatch and reliable delivery from India. Send your specification and quantity to get a price you can compare.
Ready to order Concrete Screws?
Send your quantities, grade, standard, and destination port for a quote.

